Critical evaluation of the fe–ni, fe–ti and fe–ni–ti alloy systems G Cacciamani, J De Keyzer, R Ferro, UE Klotz, J Lacaze, P Wollants Intermetallics 14 (10-11), 1312-1325, 2006 | 235 | 2006 |
Thermodynamic modeling and optimization of the Fe–Ni–Ti system J De Keyzer, G Cacciamani, N Dupin, P Wollants Calphad 33 (1), 109-123, 2009 | 137 | 2009 |
Towards a more circular economy for WEEE plastics–Part A: Development of innovative recycling strategies F Wagner, JR Peeters, J De Keyzer, K Janssens, JR Duflou, W Dewulf Waste Management 100, 269-277, 2019 | 55 | 2019 |
Construction of modified embedded atom method potentials for the study of the bulk phase behaviour in binary Pt–Rh, Pt–Pd, Pd–Rh and ternary Pt–Pd–Rh alloys J Luyten, J De Keyzer, P Wollants, C Creemers Calphad 33 (2), 370-376, 2009 | 48 | 2009 |
The influence of mechanical recycling on properties in injection molding of fiber-reinforced polypropylene T Evens, GJ Bex, M Yigit, J De Keyzer, F Desplentere, A Van Bael International Polymer Processing 34 (4), 398-407, 2019 | 35 | 2019 |
Towards a more circular economy for WEEE plastics–Part B: Assessment of the technical feasibility of recycling strategies F Wagner, JR Peeters, J De Keyzer, K Janssens, JR Duflou, W Dewulf Waste management 96, 206-214, 2019 | 31 | 2019 |
Experimental analysis of conformal cooling in SLM produced injection moulds: Effects on process and product quality T Evens, W Six, J De Keyzer, F Desplentere, A Van Bael AIP Conference Proceedings 2055 (1), 2019 | 22 | 2019 |
Wetting measurements as a tool to predict the thermoplastic/thermoset rubber compatibility in two‐component injection molding GJ Bex, D Seveno, J De Keyzer, F Desplentere, A Van Bael Journal of Applied Polymer Science 135 (13), 46046, 2018 | 22 | 2018 |
Evaluation of the quality of postconsumer plastics obtained from disassembly‐based recycling strategies F Wagner, J Peeters, J De Keyzer, J Duflou, W Dewulf Polymer Engineering & Science 58 (4), 485-492, 2018 | 19 | 2018 |
Two-component injection moulding of thermoset rubber in combination with thermoplastics by thermally separated mould cavities and rapid heat cycling GJ Bex, F Desplentere, J De Keyzer, A Van Bael The International Journal of Advanced Manufacturing Technology 92, 2599-2607, 2017 | 19 | 2017 |
Effect of process parameters on the adhesion strength in two‐component injection molding of thermoset rubbers and thermoplastics GJ Bex, W Six, B Laing, J De Keyzer, F Desplentere, A Van Bael Journal of Applied Polymer Science 135 (29), 46495, 2018 | 17 | 2018 |
The influence of melt and process parameters on the quality and occurrence of part defects in water-assisted injection molded tubes S Sannen, J De Keyzer, P Van Puyvelde International Polymer Processing 26 (5), 551-559, 2011 | 14 | 2011 |
Quality assessment of mixed plastic flakes from Waste Electrical and Electronic Equipment (WEEE) by spectroscopic techniques F Wagner, JR Peeters, H Ramon, J De Keyzer, JR Duflou, W Dewulf Resources, Conservation and Recycling 158, 104801, 2020 | 12 | 2020 |
Effect of co‐agents on adhesion between peroxide cured ethylene–propylene–diene monomer and thermoplastics in two‐component injection molding B Laing, J De Keyzer, D Seveno, A Van Bael Journal of Applied Polymer Science 137 (9), 48414, 2020 | 12 | 2020 |
Quality assessment of plastic recyclates from waste electrical and electronic equipment (WEEE): a case study for desktop computers, laptops, and tablets F Wagner, J Peeters, J De Keyzer, J Duflou, W Dewulf Technologies and Eco-innovation towards sustainability II: Eco design …, 2019 | 12 | 2019 |
Two-component injection moulding of thermoplastics with thermoset rubbers: Process development G Bex, J De Keyzer, F Desplentere, A Van Bael AIP Conference Proceedings 1914 (1), 2017 | 10 | 2017 |
Silver-Copper-Titanium O Kubaschewski, J De Keyzer, R Schmid-Fetzer, O Shcherban, ... Springer-Verlag; Berlin Heidelberg 11, 63-74, 2007 | 9 | 2007 |
Prediction of interfacial strength of HDPE overmolded with EPDM W Six, GJ Bex, A Van Bael, J De Keyzer, F Desplentere Polymer Engineering & Science 59 (7), 1489-1498, 2019 | 8 | 2019 |
Water penetration behavior in water-assisted injection molding (WAIM): a study of product quality for different process and material parameters S Sannen, M De Munck, P Van Puyvelde, J De Keyzer International Polymer Processing 27 (5), 602-616, 2012 | 8 | 2012 |
Reactive wetting of polyethylene on ethylene-propylene-diene terpolymer B Laing, D Seveno, J De Keyzer, A Van Bael Colloid and Interface Science Communications 40, 100343, 2021 | 6 | 2021 |