Follow
Soumitra Paul
Soumitra Paul
Indian Institute of Technology Kharagpur, (TU Delft and IIT Kharagpur)
Verified email at mech.iitkgp.ernet.in - Homepage
Title
Cited by
Cited by
Year
Estimation of tool wear during CNC milling using neural network-based sensor fusion
N Ghosh, YB Ravi, A Patra, S Mukhopadhyay, S Paul, AR Mohanty, ...
Mechanical Systems and Signal Processing 21 (1), 466-479, 2007
4832007
Growth of tool wear in turning of Ti-6Al-4V alloy under cryogenic cooling
KA Venugopal, S Paul, AB Chattopadhyay
Wear 262 (9-10), 1071-1078, 2007
3762007
Beneficial effects of cryogenic cooling over dry and wet machining on tool wear and surface finish in turning AISI 1060 steel
S Paul, NR Dhar, AB Chattopadhyay
Journal of Materials Processing Technology 116 (1), 44-48, 2001
2732001
Some studies on high-pressure cooling in turning of Ti–6Al–4V
AK Nandy, MC Gowrishankar, S Paul
International Journal of Machine Tools and Manufacture 49 (2), 182-198, 2009
2092009
Tool wear in cryogenic turning of Ti-6Al-4V alloy
KA Venugopal, S Paul, AB Chattopadhyay
Cryogenics 47 (1), 12-18, 2007
2062007
The influence of cryogenic cooling on tool wear, dimensional accuracy and surface finish in turning AISI 1040 and E4340C steels
NR Dhar, S Paul, AB Chattopadhyay
Wear 249 (10-11), 932-942, 2001
1972001
Machining of AISI 4140 steel under cryogenic cooling—tool wear, surface roughness and dimensional deviation
NR Dhar, S Paul, AB Chattopadhyay
Journal of Materials Processing Technology 123 (3), 483-489, 2002
1732002
Effects of cryogenic cooling by liquid nitrogen jet on forces, temperature and surface residual stresses in grinding steels
S Paul, AB Chattopadhyay
Cryogenics 35 (8), 515-523, 1995
1711995
Role of cryogenic cooling on cutting temperature in turning steel
NR Dhar, S Paul, AB Chattopadhyay
Journal of Manufacturing Science and Engineering 124 (1), 146-154, 2002
1672002
Modelling of specific energy requirement during high-efficiency deep grinding
S Ghosh, AB Chattopadhyay, S Paul
International Journal of Machine Tools and Manufacture 48 (11), 1242-1253, 2008
1432008
The effect of cryogenic cooling on grinding forces
S Paul, AB Chattopadhyay
International Journal of Machine Tools and Manufacture 36 (1), 63-72, 1996
1411996
Correlation between full width at half maximum (FWHM) of XRD peak with residual stress on ground surfaces
M Vashista, S Paul
Philosophical Magazine 93 (33), 4194-4209, 2012
1372012
A study of effects of cryo-cooling in grinding
S Paul, AB Chattopadhyay
International Journal of Machine Tools and Manufacture 35 (1), 109-117, 1995
1191995
Effect of substrate bias voltage on structural and mechanical properties of pulsed DC magnetron sputtered TiN–MoSx composite coatings
S Gangopadhyay, R Acharya, AK Chattopadhyay, S Paul
Vacuum 84 (6), 843-850, 2010
1112010
Analytical and experimental modelling of the abrasive water jet cutting of ductile materials
S Paul, AM Hoogstrate, CA Van Luttervelt, HJJ Kals
Journal of Materials Processing Technology 73 (1), 189-199, 1998
1071998
Determination and control of grinding zone temperature under cryogenic cooling
S Paul, AB Chattopadhyay
International Journal of Machine Tools and Manufacture 36 (4), 491-501, 1996
1051996
Effects of grit blasting on surface properties of steel substrates
KP Chander, M Vashista, K Sabiruddin, S Paul, PP Bandyopadhyay
Materials & Design 30 (8), 2895-2902, 2009
1042009
Numerical modelling of surface topography in superabrasive grinding
S Chakrabarti, S Paul
The International Journal of Advanced Manufacturing Technology 39 (1), 29-38, 2008
1042008
An experimental investigation of rectangular pocket milling with abrasive water jet
S Paul, AM Hoogstrate, CA Van Luttervelt, HJJ Kals
Journal of Materials Processing Technology 73 (1), 179-188, 1998
901998
Effects of cryo-cooling in grinding steels
S Paul, PP Bandyopadhyay, AB Chattopadhyay
Journal of Materials Processing Technology 37 (1-4), 791-800, 1993
851993
The system can't perform the operation now. Try again later.
Articles 1–20